BioTransducer® Pro

Non-invasive relief.

BioTransducer® technology is a new approach to health care for the 21st Century. The BioTransducer® provides therapy that addresses the underlying cause of pain and inflammation without drugs or invasive medical procedures.

FAQ

Most frequently asked questions and answers.

BioTransducer® Technology provides no-touch, painless therapy. The Tennant BioModulator® transmits frequencies and voltage that the BioTransducer® delivers on a carrier wave into the tissue, through skin and bone. Using the BioTransducer® to deliver the frequencies and voltage speeds up therapy time.

The BioTransducer® is not a laser. The BioTransducer® can be used through clothing allowing the BioModulator® therapies to be delivered anywhere on the body without the need for direct skin contact.

Some users experience a subtle tingle or sensation of warmth from the BioTransducer®. Most people don’t feel any sensations when using the BioTransducer®. You may feel initial apprehension about providing therapy to yourself or others. When you carefully follow the instructions and directions, there’s no need to be concerned. The devices and therapy steps were created with the knowledge that application will be general and does not have to be precisely aligned with any given point of the body. Even if you are providing the therapy to a different area than intended, it is not harmful and, in most cases, will still benefit you.

If you are familiar with our BioTransducer® Crystal Wave, you know that it is powered solely from the BioModulator®. The BioTransducer® Pro is much stronger, therefore requires the additional power from the internal lithium battery. Be sure both the BioTransducer® Pro power and the BioModulator® are turned on when you are doing treatments. 

Setting Up Your BioTransducer® Pro

Connect the USB cord to your BioTransducer® Pro and the A/C adaptor to charge

• It takes 6 hours to charge to full capacity and therefore should be charged overnight.

• One charge lasts 3 days, depending on use

• It is best to treat it like a cell phone, don’t run the battery completely down

PLEASE NOTE: Prior to using your BioTransducer® Pro for therapy, you must balance the polarity of your body. Refer to the Daily Protocol Guide for instructions on balancing polarity.

Read & download the full PDF on the Daily Protocol here.

 

INSTRUCTIONS FOR USE

1. Connect the BioTransducer® to the Tennant BioModulator® with the connection wire. Use care when plugging the wire into the port on the BioModulator®. You can cause damage to your BioModulator® if it is knocked or bumped when plugged in. It is very important to remove the plug when not in use.

2. Turn on your BioModulator® (Pro or Plus).

3. Set the mode.

For BioModulator® Plus:

• TEN-8 for pain and inflammation related to muscle, bone, ligament and tendons. 

• INFINITY for all other issues related to organs and general health. 

• INFINITY for eye treatment.

For BioModulator® Pro:

• TEN-8 for pain and inflammation related to muscle, bone, ligament and tendons. 

• INFINITY for all other issues related to organs and general health. 

• VA-STEP for eye treatment. 

4. Adjust the power by pressing the + and – buttons. Since there is no skin contact you may increase the power as high as you want when using it on the body. When using it on the eyes set the power as is indicated in the eye treatment section (pg 7). 

5. Point the BioTransducer® at the area of concern, holding it between 1⁄2 an inch to 3 inches away from the body. (Please note: If you rest the rubber cap against the skin, you may have an allergic reaction to the rubber.) 

6. As a general guideline, therapy times are flexible just as they are when using the BioModulator® alone. 

For example:

a) 5 – 15 minutes for minor issues and for general use. 

b) As long as needed for more serious conditions. 

Tip: Therapy can continue for several hours when you mount the BioTransducer® to a mic stand and position it on the area of concern. See pg. 9 of the Quick Start Guide for caring for your batteries when doing longer therapy sessions. 

NOTE: You must have a BioModulator® device to complete this protocol.

This daily protocol will help balance and prepare your body so it can properly receive and use the voltage provided by your BioModulator® device for healing. This is accomplished by waking up and “activating” your organ systems, resetting your polarity so electrons flow correctly, balancing your autonomic nervous system, and recharging your whole body.

Click Here to read & download the full PDF on the Daily Protocol

Click Here to watch the Daily Protocol How-To Video

Click here to read an introduction to Healing is Voltage™, everything you need to know about getting started with your devices & Dr. Tennant’s Health System.

Also, you can download this detailed instructional guide on how to care for and use your BioModulator® Pro to its fullest potential.

Click Here for the BioTransducer® PRO QUICK START GUIDE.

You can purchase Dr. Tennant’s Tennant BioTransducer® Pro at this link.

Questions? Concerns? Contact Senergy at 972-580-0545 or send an email to live.well@senergy.us.

Shopping Cart